Trustpilot4.1/5 · 25 reviews
Skip to main content

Nonsensia

In a published impurity study of the antimalarial lumefantrine, one degradation product was found in market samples at between 0.03 and 0.12 percent, measured by area normalisation. The same paper reports its relative response factor against lumefantrine at 266 nm as 2.87. Both statements are in the same article, and together they say something uncomfortable: the reported figure overstated the real amount by nearly a factor of three.

That gap is the difference between area percent and mass percent, and it is the single most misread line on a certificate of analysis.

The difference between area percent and mass percent

Area percent is the integrated area of one peak divided by the summed area of all peaks in a chromatogram, expressed as a percentage. It is internal to the run. Nothing is weighed, nothing is calibrated, no reference material is required.

Mass percent (also mass fraction, or percent by weight) is the mass of the analyte divided by the mass of the sample. It is a physical quantity that can be traced back to a balance.

The two coincide only when the detector produces the same signal per unit mass for every compound in the sample. That condition is convenient, commonly assumed, and rarely true.

Why detector response is compound-specific

An ultraviolet detector does not weigh molecules. It measures how much light they absorb at a chosen wavelength, which is a property of their electronic structure. A conjugated aromatic impurity and a saturated fragment of the same molecule can pass through the same flow cell in identical amounts and produce wildly different peaks.

The ratio is captured by the relative response factor (RRF). In the lumefantrine work it is defined as the ratio of the peak area of the compound to the peak area of lumefantrine, both injected at the same concentration. For the desbenzylketo derivative that ratio was 2.87.

Run that backwards and the arithmetic is unforgiving. An impurity peak reported as 1.00 area percent, with an RRF of 2.87, corresponds to roughly 0.35 percent by mass relative to the main compound. The chromatogram was not lying; it simply answered a different question from the one the reader asked.

The error runs the other way just as easily. A hypothetical impurity with an RRF of 0.2 – a weak absorber at the working wavelength – appearing as a modest 0.10 area percent peak would represent something closer to 0.5 percent by mass. Nothing about the chromatogram flags which case you are in. Only an independently determined response factor does.

What ICH permits when response factors are not close

Regulatory guidance is explicit that this is an assumption rather than a measurement. ICH Q3A(R2), whose current Step 4 version is dated 25 October 2006, accepts that the drug substance itself can be used as a standard to estimate impurity levels, and adds that where the response factors of the substance and the relevant impurity are not close, the practice can still be appropriate provided a correction factor is applied or the impurities are, in fact, being overestimated. It goes further, stating that acceptance criteria and procedures for estimating impurities can be based on analytical assumptions (e.g., equivalent detector response) and that these assumptions should be discussed in the registration application.

ICH Q2(R2), adopted on 1 November 2023, puts a number on the tolerance. For separation techniques used for impurities or assay, it directs that where an analyte responds differently from the reference material – for instance a different specific UV absorbance – relative response factors should be calculated from the appropriate ratio of responses, and that if the relative response factor is outside the range 0.8-1.2, then a correction factor should be applied. If an impurity or degradation product is overestimated, it may be acceptable not to correct.

The asymmetry is the point. Overestimating an impurity is the safe direction of error, so a batch that looks worse than it is can be tolerated. An error that makes it look cleaner than it is cannot.

That window is achievable in practice. A 2023 method for nine related substances in ursodeoxycholic acid, a compound whose impurities lack chromophores, used charged aerosol detection and reported correction factors all within the range 0.8-1.2 after optimisation, which made it feasible to quantify every impurity against a single reference substance rather than one standard per impurity.

How a mass percent value is actually established

If area percent will not give you percent by weight, something else has to. The classical route is the mass balance approach. A 2024 purity assignment of tripropyl phosphate describes it as an indirect method that measures the content of various types of impurities separately, using different detection techniques, and then deducts them from 100 percent. The classes are structure-related organic impurities, water, residual organic solvents and inorganic impurities, handled in that study by chromatography, Karl Fischer titration, headspace GC with flame ionisation detection, and ICP-MS respectively.

Mass balance answers the right question but has a structural blind spot: it can only subtract what somebody looked for. That is why the same study runs quantitative NMR alongside it, noting that qNMR resolves the limitation of the mass balance method, which might not identify all impurities. qNMR compares integrated nuclear signals against a certified internal standard, so its response depends on the number of nuclei rather than on a chromophore.

Where impurity standards are unavailable, response factors can also be measured rather than assumed. A 2008 case study determined the relative response factors of paclitaxel-related impurities using HPLC with ultraviolet and charged aerosol detectors in tandem, reporting that the CAD peak response was independent of analyte structure in the isocratic analysis used, which allowed RRFs to be calculated for unknown impurities without obtaining authentic pure materials. A 2022 study took a comparable route with photodiode array and evaporative light scattering detection for cefathiamidine impurities, applying peak area correction and cross-checking the resulting RRF values by qNMR.

Two certificates, two different claims

Area percent Mass percent
What is divided by what One peak area over total peak area Analyte mass over sample mass
Reference material needed None Yes, or a primary method
Assumes equal detector response Yes, unless RRFs are applied No
Sees water No Yes, via Karl Fischer titration
Sees residual solvents No Yes, via headspace GC
Sees inorganic residues No Yes, via ICP-MS or equivalent
Typical label wording “99.5% (HPLC, area)” “99.5% (mass balance)” or “assay 99.5%”

Two bottles labelled 99.5 percent can therefore describe different physical realities. One may contain 0.5 percent of related substances by area and an unstated amount of water and solvent on top. The other may already have water, solvents and ash subtracted. An area percent figure does not include water, solvent or ash, so there is no way to convert one label into the other.

What to ask before treating an area percent as a mass

  • Was it area normalisation or an assay? Only the second is anchored to a weighed reference.
  • At what wavelength? Response factors are wavelength-dependent, so the same sample can give different area percentages at 210 and 254 nm.
  • Were RRFs determined, and corrections applied? ICH Q2(R2) sets 0.8-1.2 as the window outside which a correction factor should be used.
  • Is water reported separately? A hygroscopic solid can carry a mass fraction of water that no chromatogram shows.
  • Are residual solvents and elemental impurities on the document? If not, they are unmeasured rather than absent.

None of this makes area percent a bad number. It is a fast, sensitive and genuinely informative measure of the related-substance profile of a sample, and for comparing successive batches from the same process it is often the most useful figure available. The failure mode is only ever the silent conversion – reading a signal ratio as though it were a statement about weight. Material used as an analytical reference in laboratory work deserves the more careful reading.

Frequently asked questions

Is 99.5 area percent the same as 99.5 percent by weight?

No. Area percent is the share of total chromatographic peak area belonging to the main peak. Percent by weight is a mass fraction. They agree only if every compound in the sample gives the same detector signal per unit mass, which is rarely true. Water, solvents and inorganic residues are also excluded from an area percent figure.

How do you convert area percent to mass percent?

You cannot convert reliably from the label alone. A correct conversion needs the relative response factor of each impurity against the main compound at the working wavelength, plus separate determinations of water, residual solvents and inorganic content. Without those, any conversion is an assumption of equivalent detector response rather than a calculation.

What is a relative response factor in HPLC?

It is the ratio of the detector response of one compound to the response of a reference compound, both measured at the same concentration under identical chromatographic conditions. An RRF of 2.87 means the compound gives almost three times the peak area of the reference for the same amount, so its raw area percent overstates its mass fraction.

When does a correction factor have to be applied?

ICH Q2(R2) states that if the relative response factor falls outside the range 0.8 to 1.2, a correction factor should be applied. Within that window the difference is treated as tolerable. The guideline adds that where an impurity or degradation product is being overestimated, applying no correction may still be acceptable.

Why do response factors differ between impurities?

Because ultraviolet response depends on the chromophore of each molecule at the chosen wavelength, not on its mass. Losing a conjugated ring, gaining a carbonyl or shifting a double bond changes absorbance substantially. Impurities are structurally related to the parent compound but not identical to it, so their responses scatter around it rather than matching it.

What does the mass balance method measure?

It measures purity indirectly by quantifying each class of impurity with a technique suited to it and subtracting the total from 100 percent. Published work covers structure-related organic impurities, water by Karl Fischer titration, residual organic solvents by headspace GC-FID, and inorganic impurities by ICP-MS. Its weakness is that undiscovered impurities are never subtracted.

References

  1. ICH, Validation of Analytical Procedures Q2(R2), final version adopted 1 November 2023
  2. ICH, Impurities in New Drug Substances Q3A(R2), Step 4 version dated 25 October 2006
  3. Verbeken M. et al., Stability-indicating HPLC-DAD/UV-ESI/MS impurity profiling of the anti-malarial drug lumefantrine, Malaria Journal, 2011
  4. Wan Y. et al., Purity Assessment of Tripropyl Phosphate through Mass Balance and 1H and 31P Quantitative Nuclear Magnetic Resonance, Molecules, 2024
  5. Huang Y. et al., Development of HPLC-CAD method for simultaneous quantification of nine related substances in ursodeoxycholic acid, Journal of Pharmaceutical and Biomedical Analysis, 2023
  6. Sun P., Wang X., Alquier L., Maryanoff C.A., Determination of relative response factors of impurities in paclitaxel with HPLC equipped with ultraviolet and charged aerosol detectors, Journal of Chromatography A, 2008
  7. Zhu L. et al., A novel method for determining relative response factors using HPLC with photodiode array detector and evaporative light scattering detection, Phytochemical Analysis, 2022

Research use only. Nonsensia supplies analytical reference standards for laboratory and research applications. This article is published for scientific and educational purposes. It is not medical advice, it does not describe any use in humans, and nothing in it should be read as a recommendation to administer any substance to a person or animal.

Filed under: Analytical Methods

This article is part of our guide to Identity and Purity: A Complete Guide to Analytical Methods for Small Molecules.